Horizontal Fence Calculator

Estimate horizontal slat rows, 6 ft anti-sag posts, center stiffener battens, concrete bags, and a material cost range.

MODERN SLAT TAKEOFFFormulas & sources
+ Footing, concrete & unit pricesDefault: 10" × 30" fill · 80 lb

Enter the concrete fill depth, not the full hole depth. Subtract 4–6 in for gravel if your hole is dug deeper than the concrete plug.

Defaults last reviewed 2026-11-18. Illustrative U.S. baseline prices for planning only. Edit every field to match your local store. Excludes labor, permits, sales tax, and gate construction.

LIVE HORIZONTAL SLAT ELEVATION (SCHEMATIC)6 FT · 6 FT BAY · 13 ROWS
6 FTSPAN: 6 FT · 13 HORIZONTAL ROWSSCHEMATIC · NOT TO SCALE
Posts17
Boards229
Bags43

Direct answer: 96 ft horizontal fence

For a 96 ft, 6 ft high horizontal fence with 6 ft post spacing, 5.5 in slats, 0.25 in gaps, and a center stiffener: 17 posts, 13 rows per bay, 229 boards with 10% waste, 16 battens, and 43 bags of 80 lb concrete for 10 in × 30 in holes. A gate subtracts from the fence length and adds two gate posts.

Horizontal fence board row formula

A horizontal fence stacks boards lengthwise between posts. The number of rows is set by the fence height and the board width plus gap. The number of board pieces is the number of rows multiplied by the number of bays. This calculator assumes one board per row per bay; if you use long boards that span multiple bays, the board count will be lower, but joints and waste change.

Rows per bay = ceil(height × 12 ÷ (slat width + gap))
Bays = ceil(effective length ÷ post spacing)
Net boards = rows per bay × bays
Order boards = ceil(net boards × (1 + waste))
Battens = bays (when the center stiffener is enabled)

Why 6 ft post spacing is the default

Horizontal boards are usually 1-inch nominal thickness. They span between posts and carry their own weight plus wind load, so they are more sensitive to span than vertical pickets. Six ft on-center is the common residential recommendation. At 8 ft spacing, the boards are more likely to sag or cup, especially in summer heat; a center vertical stiffener or a heavier framing plan is needed.

A center stiffener batten is not just a cosmetic divider. It shortens the effective span of each board and helps keep the rows aligned. The calculator adds one batten per bay when the option is enabled, but it does not engineer the connection. Fasten and size the batten for your local wind and board weight.

Board count, waste, and board length

The default waste buffer is 10%. That covers cutoffs, defects, and a few miscuts. If your layout has many short returns, gates, or diagonal terminations, use 15%. If you are building a single straight run with long boards, 5–10% may be enough.

The board count assumes each board is cut to one bay. A 16 ft board spanning two 8 ft bays would reduce the number of pieces but increase handling and waste. Decide your board length and joint layout before ordering; the calculator is a quantity estimate, not a cut list.

Concrete, gravel, and footing depth

The concrete calculation uses the number of posts, hole diameter, concrete fill depth, bag yield, and overage. A 10 in hole with a 30 in fill holds about 1.36 ft³. At 0.60 ft³ per 80 lb bag, that is 2.27 bags per hole before overage. The calculator rounds up to whole bags.

Put 4–6 in of crushed gravel at the bottom of the hole for drainage, then pour concrete to the fill depth. Do not enter the full hole depth if part of it is gravel. Frost depth and permit requirements vary by state and municipality; call 811 before digging and verify the local requirement.

Horizontal vs. vertical fence: what changes

ItemVerticalHorizontal
Post spacing6–8 ft6 ft recommended
Framing2×4 rails, pickets nailed to railsBoards stacked between posts; center batten
Material countPickets + railsBoard rows × bays + battens
PrivacyTighter with small gapsGaps between rows; less solid unless backed

Frequently Asked Questions

How many boards do I need for a 96 ft horizontal fence?

With 6 ft post spacing, 6 ft height, 5.5 in slats, and a 0.25 in gap, you need 13 rows per bay and 16 bays — 208 net boards. With a 10% waste allowance, order 229 boards.

How many posts does a horizontal fence need?

At 6 ft on-center, a 96 ft run needs 17 posts. If the run includes a 4 ft gate, the fence is split into two sections and the total becomes 18 posts, including the two gate posts.

Do I need a center stiffener batten?

A center vertical batten is strongly recommended for 1-inch horizontal boards at 6 ft spacing. It reduces sag and warping. If you use 8 ft post spacing, a stiffener or engineered framing is even more important. The calculator adds one batten per bay when the box is checked.

How many bags of concrete for 17 posts?

For 17 holes at 10 in diameter and 30 in concrete fill, each hole holds about 1.36 ft³. At 0.60 ft³ per 80 lb bag with 10% overage, you need 43 bags. Enter the concrete fill depth, not the full hole depth, if you use a gravel base.

Can I use 8 ft post spacing for a horizontal fence?

Only if the framing is designed for it. Horizontal 1-inch boards span between posts and are more prone to sag than vertical pickets on rails. Six ft on-center is the common recommendation; 8 ft usually needs a center stiffener or a heavier board and is best confirmed with a contractor.

Does the horizontal calculator include gate framing?

It subtracts the gate opening from the fence length and adds two gate posts per gate. It does not design the gate frame, hinges, latch, or diagonal bracing. Gate construction should be sized for the gate width and weight.

Connected tools & field guides